10 Advantages of Hydraulic Press Machine

2016-11-19 10:35:50

What are the advantages of hydraulic press machine? Please see this page.

Full power stroke

The full power of a hydraulic press machine can be delivered at any point in the stroke. Not only at the very bottom, as is the case with mechanical presses. Advantages? No allowances for reduced tonnage at the top of the stroke. In drawing operations, for example, you have the full power of the press available at the top of the stroke. You don't have to buy a 200-ton press to get 100 tons throughout the stroke. Other advantages are faster set-ups and no time consuming job of adjusting the stroke nut on the slide to accommodate different dies.


Built-in overload protection

A 100-ton hydraulic press will exert only 100 tons of pressure (or less, if you have set it for less) no matter what mistakes you make in set-up. You needn't worry about overloading or breaking the press or smashing a die. When a hydraulic press reaches its set pressure, that's all the pressure there is. The relief valve opens at that limit and there is no danger of overload.


Much lower original cost and operating costs

Hydraulic presses are relatively simple, and you may be surprised at the significant cost advantage over mechanical presses in comparable sizes. The numbers of moving parts are few, and these are fully lubricated in a flow of pressurized oil. Breakdowns, when they occur, are usually minor; not, for example, like a broken crankshaft. Replacements of packing, solenoid coils, and occasionally a valve, are typical maintenance items. Not only are these parts inexpensive, but also they are easily replaced without tearing the machine apart. This means more up-time and lower maintenance costs.


Larger capacities at lower cost

It is easier and less expensive to buy certain kinds of capacity in hydraulic presses. Stroke lengths of 12, 18, and 24 inches are common. Extra stroke length is easy to provide. Open gap (daylight), too, can be added without much additional cost. Similarly, larger table areas and small presses with big bed areas can be provided. Large 200-ton presses with relatively small beds are available; tonnage of the press doesn't dictate what the bed size will be.


More control flexibility

Hydraulic press power is always under control. The ram force, the direction, the speed, the release of force, the duration of pressure dwell, all can be adjusted to fit a particular job. Jobs with light dies can be done with the pressure turned down. The ram can be made to approach the work rapidly, then shifted to a slower speed before contacting the work. Tool life is thus prolonged. Timers, feeders, heaters, coolers, and a variety of auxiliary functions can be brought into the sequence to suit the job. Hydraulic presses can do far more than just go up and down, up and down.


Greater versatility

A single hydraulic press can do a wide variety of jobs within its tonnage range. Commonly seen are deep draws, shell reductions, urethane bulging, forming, blank and pierce, stake, punch, press fits, straightening, and assembly. They are also used for powered metal forming, abrasive wheel forming, bonding, broaching, ball sizing, plastic and rubber compression, and transfer molding.


Quiet

Fewer moving parts and the elimination of a flywheel reduce the overall noise level of hydraulic presses compared to mechanical presses. Properly sized and properly mounted pumping units meet and exceed current Federal standards for noise, even with the pump under full pressure.

Because each phase of the ram movement can be controlled, noise levels can also be controlled. A hydraulic ram can be controlled to pass through the work slowly and quietly.

More compact

A typical 20-ton hydraulic press is eight feet high, six feet deep, and two feet wide. A 200-ton press is only ten feet high, nine feet deep, and a little over three feet wide. At ten times the capacity, the 200-ton press only takes up 50 percent more floor space. Hydraulic presses become less and less expensive compared to mechanical presses.


Lower tool costs

the built-in overload protection (see advantage 2) goes for the tools, too. If they are built to withstand a certain load, there is no danger of damaging them because of overloading. Tools can be sized to withstand the load of a particular job, not a particular press. The pressure of the press can be set down to suit the job. The lack of impact, shock, and vibration promotes longer tool life.


Safety

No manufacturer will (or should) claim that hydraulic presses are safer than mechanical presses. Both types of machines are designed and built to be safe if the controls and safety features built in are used properly.

Improperly used, all machines are potentially dangerous. But the factor of control of the ram movements makes hydraulic presses easy to make safe. Non-tie down, anti-repeat, dual palm button controls are used. The interlocking of guards, as well as other safety devices, is relatively easy because of the nature of a hydraulic press control system.

Products