Tips to Double the Life of the Hydraulic Press Machine
2024-06-15 16:08:57
The working principle of servo hydraulic press machine is that the servo motor directly drives the gear pump for oil supply, the pressure is stable, the downward repeated positioning accuracy of the main shaft of the servo press is high, the pump control technology is adopted, energy saving and environmental protection, good rigidity, low noise, high efficiency, good flexibility, and the hydraulic servo system has been widely used in industrial control with its unique advantages such as fast response speed, large load rigidity and large control power.
1. The numerical input of the pressing depth, holding time and pressure can be carried out on the operating table, and the operation is very simple.
2. When the servo hydraulic press is press-fitting, the whole process of pressure and displacement can be displayed on the liquid crystal display frequency, which can manage the whole process of press-fitting online, and can also judge whether the product is qualified at any stage, and can remove defective products in time.
3. Its outer end is connected to the computer, which can press and save the data to the computer, so as to ensure the traceability of the data and facilitate management.
Basic operation of servo press_Two buttons start at the same time
1. Parameter setting state, press the two buttons with both hands, the pressure head slides slowly, when any button is released, the pressure head is saved in the current position, continue to press, and the pressure head continues to slide. When both buttons are released at the same time, the pressure head slowly glides back into place.
2. In the running state, as the trigger signal for the start of the equipment, the start-up mode is divided into the following types:
○ Two-hand trigger start, in the working environment with grating protection, set the electronic press to two-hand trigger start mode, press the start button with both hands at the same time within 1 second, and the electronic press will automatically start and complete a working cycle.
○ Two-hand continuous start, in the working environment without external grating protection, set the electronic press to two-hand continuous start mode, press the start button with both hands at the same time within 1 second and press and hold the button until a working cycle is completed, if any button is released in the press-fitting process, the electronic pressure stops at the current position, and the alarm is given.
○ Single-cycle press-fitting mode, start a device to complete a working cycle, this mode is suitable for press-fitting connection of parts.
○ Reciprocating cycle test mode, use this mode to turn off the start mode function, in this mode, press the left button to start the equipment to start the reciprocating to complete the same press-fitting program, and press the right button to complete the cycle press-fitting operation, this mode is suitable for product fatigue test.
3. In the pressure calibration mode, press the left button to move the pressure head downward, and press the right button to move upward.
Emergency stop: In any state as an emergency stop, in the event of an emergency, press the emergency stop button, the hydraulic press machine will be in a suspended state, the machine can not enter the next action, only manually rotate the button counterclockwise, so that the button can operate normally after release.
1. The numerical input of the pressing depth, holding time and pressure can be carried out on the operating table, and the operation is very simple.
2. When the servo hydraulic press is press-fitting, the whole process of pressure and displacement can be displayed on the liquid crystal display frequency, which can manage the whole process of press-fitting online, and can also judge whether the product is qualified at any stage, and can remove defective products in time.
3. Its outer end is connected to the computer, which can press and save the data to the computer, so as to ensure the traceability of the data and facilitate management.
Basic operation of servo press_Two buttons start at the same time
1. Parameter setting state, press the two buttons with both hands, the pressure head slides slowly, when any button is released, the pressure head is saved in the current position, continue to press, and the pressure head continues to slide. When both buttons are released at the same time, the pressure head slowly glides back into place.
2. In the running state, as the trigger signal for the start of the equipment, the start-up mode is divided into the following types:
○ Two-hand trigger start, in the working environment with grating protection, set the electronic press to two-hand trigger start mode, press the start button with both hands at the same time within 1 second, and the electronic press will automatically start and complete a working cycle.
○ Two-hand continuous start, in the working environment without external grating protection, set the electronic press to two-hand continuous start mode, press the start button with both hands at the same time within 1 second and press and hold the button until a working cycle is completed, if any button is released in the press-fitting process, the electronic pressure stops at the current position, and the alarm is given.
○ Single-cycle press-fitting mode, start a device to complete a working cycle, this mode is suitable for press-fitting connection of parts.
○ Reciprocating cycle test mode, use this mode to turn off the start mode function, in this mode, press the left button to start the equipment to start the reciprocating to complete the same press-fitting program, and press the right button to complete the cycle press-fitting operation, this mode is suitable for product fatigue test.
3. In the pressure calibration mode, press the left button to move the pressure head downward, and press the right button to move upward.
Emergency stop: In any state as an emergency stop, in the event of an emergency, press the emergency stop button, the hydraulic press machine will be in a suspended state, the machine can not enter the next action, only manually rotate the button counterclockwise, so that the button can operate normally after release.
TOP
WINDOWS